Skip to main content
numora.
numora.

Crosswind Component Calculator: Resolve Wind to the Runway

Crosswind and headwind components for a runway

AviationBy Numora Aviation TeamNot yet reviewed

Try the calculator

Math runs in your browser. No sign-up.

Assumptions
kt
°
Crosswind component
10

Check against the aircraft's demonstrated crosswind limit.

20kt kt at 30°° gives 10 kt across and 17.32 kt down the runway.

Headwind component17.32
Share of wind across runway50
Embed this calculator on your own site — drop in a one-line iframe.
Quick takeaway

Wind is reported as a direction and speed, but what matters on approach is how that wind resolves relative to the runway. The component along the runway is headwind or tailwind; the component across it is crosswind, and it is the figure checked against the aircraft's demonstrated crosswind limit. The trigonometry is straightforward — crosswind is wind speed times the sine of the angle between wind and runway, headwind is wind speed times the cosine — but the angles are worth committing to memory, since a 30° offset puts half the wind across the runway and a 60° offset puts 87% across it. A negative headwind result means a tailwind, which lengthens the landing roll considerably.

What is a crosswind component?

Resolve a reported wind into crosswind and headwind components relative to runway heading. Crosswind is wind speed times the sine of the offset angle and headwind is the cosine — so a 30° offset puts half the wind across the runway while 87% still helps on approach, and a 60° offset reverses that balance. Compare the crosswind figure against your aircraft's demonstrated value and your own currency, and run it against the gust rather than the steady wind.

The formula

crosswind = V × sin(θ) · headwind = V × cos(θ)

Source: Vector resolution of reported surface wind.

Worked examples

1A 30-degree offset

Inputs
windSpeed: 20windAngle: 30
Walkthrough

Twenty knots at 30° off gives a 10-knot crosswind and 17.3 knots of headwind. Half the wind is across the runway while 87% still helps on approach — the reason a 30° offset is generally comfortable in most light aircraft. If gusting to 28, the crosswind would be 14 knots, which is the number worth planning against.

2A 60-degree offset at lower speed

Inputs
windSpeed: 15windAngle: 60
Walkthrough

Fifteen knots at 60° off gives a 13-knot crosswind and only 7.5 knots of headwind. Despite the lower wind speed, the crosswind component exceeds the first example. This is the key insight: angle matters as much as speed, and a modest wind well off the runway can exceed a strong wind nearly aligned with it.

How to use this calculator

  1. Wind speed (default: 20)
  2. Angle to runway — Difference between wind direction and runway heading. 0° is straight down the runway; 90° is directly across.
  3. Read the result. Use the worked examples below to sanity-check against a known scenario.

Common mistakes and edge cases

Using the wrong angle

The angle is between wind direction and runway heading, not between wind direction and north. Runway 09 is 090°, so a 120° wind is 30° off, not 120°.

Calculating from steady wind rather than gusts

Reported wind is typically a two-minute average. Run the numbers against the gust value, since that is what you will have to control for in the flare.

Treating demonstrated crosswind as a certified limit

For most light aircraft it is a value shown during certification, not a regulatory maximum. It reflects test conditions and a test pilot, and personal limits should sit well below it.

Confusing magnetic and true wind

Tower-reported winds are magnetic, matching runway numbers. Forecast and METAR winds are often true. Mixing them introduces an error equal to local magnetic variation.

Frequently asked questions

how do I calculate a crosswind component
Multiply wind speed by the sine of the angle between the wind and the runway. Twenty knots at 30° off gives 20 × 0.5 = 10 knots of crosswind.
what angle gives half the wind as crosswind
Thirty degrees, since sin(30°) = 0.5. At 45° it is about 70%, at 60° about 87%, and at 90° the entire wind is crosswind.
should I use the steady wind or the gust
The gust. Reported wind is a two-minute average, and the peak is what you will be controlling for during the flare.
is demonstrated crosswind a legal limit
For most light aircraft, no — it is the value shown during certification testing, under favourable conditions with a test pilot. Personal limits should be lower.
what does a negative headwind mean
A tailwind, which occurs beyond 90° of offset. Even a few knots meaningfully lengthens the landing roll and should be taken seriously.

Crosswind Component glossary

Crosswind component
The part of the wind acting perpendicular to the runway, equal to wind speed × sin(angle).
Headwind component
The part acting along the runway toward the aircraft, equal to wind speed × cos(angle). Negative values are tailwind.
Demonstrated crosswind
The maximum crosswind shown during certification testing. For most light aircraft an advisory figure, not a regulatory limit.
Gust factor
The difference between steady and peak reported wind. Crosswind planning should use the gust value.

How we built this calculator

Methodology

A wind vector resolves into two perpendicular components relative to the runway. Basic trigonometry gives the split: the component across the runway is V sin θ and the component along it is V cos θ, where θ is the angle between the wind and the runway heading.

Formula source
Vector resolution of reported surface wind
Last updated
2026-11-17
Calculation runs
Client-side only
NA
WRITTEN BY
Numora Aviation Team

Sources & references

Every numeric assumption traces to a primary source.

  1. U.S. Federal Aviation Administration — Airplane Flying Handbook (FAA-H-8083-3)USA
  2. U.S. Federal Aviation Administration — Aeronautical Information ManualUSA
  3. National Weather Service — Aviation Weather Services (AC 00-45)USA
  4. Numora Editorial Policy. numora.net/editorial-policy