Skip to main content
numora.
numora.

Gear Ratio Calculator: Work Out Any Gear Train

Ratio, output speed and torque multiplication

EngineeringByΒ Numora Engineering TeamNot yet reviewed

Try the calculator

Math runs in your browser. No sign-up.

Assumptions
RPM
Nm
Gear ratio
3

Above 1 is a reduction; below 1 an overdrive.

12 into 36 teeth is a 3:1 ratio, giving 600 RPM.

Output speed600
Output torque150
Torque multiplication3
Embed this calculator on your own site β€” drop in a one-line iframe.
Quick takeaway

A gear ratio is the ratio of teeth on the driven gear to teeth on the driver, and it governs the fundamental trade in mechanical transmission: speed for torque, in exact inverse proportion. A 3:1 reduction turns the output at one third the input speed while multiplying torque threefold, minus losses. Ratios above 1 are reductions, slowing the output and increasing torque; ratios below 1 are overdrives, doing the reverse. Because power is conserved, the product of speed and torque stays constant apart from friction β€” which is why no gearbox can increase both and why claims to the contrary are always wrong.

What is a gear ratio?

Calculate gear ratio, output speed and torque multiplication from driver and driven tooth counts. The ratio governs the fundamental trade in mechanical transmission β€” speed for torque, in exact inverse proportion, because a gearbox cannot create power. A 3:1 reduction turns the output at a third the speed with three times the torque, minus the 2–3% per stage that friction consumes.

The formula

ratio = driven teeth Γ· driver teeth; output RPM = input Γ· ratio; output torque = input Γ— ratio

Source: Ideal gear train kinematics.

Worked examples

1A 3:1 reduction drive

Inputs
driverTeeth: 12drivenTeeth: 36inputRpm: 1800inputTorque: 50
Walkthrough

Twelve teeth driving thirty-six gives 3:1. An 1,800 RPM motor delivering 50 Nm produces 600 RPM at 150 Nm. Power is identical on both sides apart from friction: 50 Γ— 1,800 and 150 Γ— 600 are the same product. Allowing 3% for mesh losses, expect about 145 Nm in practice.

2An overdrive arrangement

Inputs
driverTeeth: 20drivenTeeth: 15inputRpm: 3000inputTorque: 50
Walkthrough

A larger gear driving a smaller one gives 0.75:1, raising 3,000 RPM to 4,000 while reducing torque from 50 Nm to 37.5. This is the top-gear arrangement in a car gearbox, chosen when an engine makes ample torque and the need is for road speed at low engine revolutions.

How to use this calculator

  1. Driver gear teeth β€” The input gear, connected to the power source.
  2. Driven gear teeth β€” The output gear.
  3. Input speed (default: 1800)
  4. Input torque (default: 50)
  5. Read the result. Use the worked examples below to sanity-check against a known scenario.

Common mistakes and edge cases

Inverting the ratio

The ratio is driven over driver, not the reverse. Getting it backwards turns a 3:1 reduction into a 0.33:1 overdrive and reverses every conclusion that follows.

Expecting more speed and more torque together

A gearbox trades one for the other. Any arrangement claiming to increase both is either mistaken or quietly adding power from elsewhere.

Ignoring efficiency losses

Each meshing stage costs roughly 2–3%. A multi-stage reduction delivers noticeably less torque than the ideal figure, and the losses compound.

Forgetting direction reversal

An external gear pair reverses rotation. Idler gears are often inserted purely to correct direction without changing the overall ratio, since an idler's tooth count cancels out.

Frequently asked questions

how do I calculate gear ratio
Divide the driven gear's teeth by the driver's. Twelve teeth driving thirty-six gives 36 Γ· 12 = 3, written 3:1.
does a gear ratio increase torque or speed
One at the expense of the other. A reduction multiplies torque and divides speed; an overdrive does the reverse. Power is conserved apart from friction.
what is a 3 to 1 gear ratio
The driver turns three times for one turn of the driven gear. Output speed is a third of input and torque is tripled.
how do I calculate a multi-stage gearbox
Multiply the ratios of each stage. Two 3:1 stages give 9:1 overall, with efficiency losses compounding at roughly 2–3% per mesh.
why do gearboxes use idler gears
To reverse rotation direction without changing the ratio. An idler's tooth count cancels out of the overall calculation.

Gear Ratio glossary

Gear ratio
Driven teeth divided by driver teeth. Above 1 is reduction; below 1 is overdrive.
Reduction drive
A gear arrangement decreasing output speed and increasing torque proportionally.
Overdrive
A ratio below 1:1, increasing output speed at the cost of torque.
Idler gear
A gear inserted to reverse rotation direction without affecting the overall ratio, since its tooth count cancels.

How we built this calculator

Methodology

Gear ratio is the tooth count of the driven gear divided by that of the driver. A 12-tooth gear driving a 36-tooth gear gives 36 Γ· 12 = 3, written 3:1. The driver must complete three turns for the driven gear to complete one.

Formula source
Ideal gear train kinematics
Last updated
2026-11-17
Calculation runs
Client-side only
NE
WRITTEN BY
Numora Engineering Team

Sources & references

Every numeric assumption traces to a primary source.

  1. American Gear Manufacturers Association β€” ANSI/AGMA 2001 Fundamental Rating FactorsUSA
  2. ISO 6336 β€” Calculation of load capacity of spur and helical gearsINT
  3. NASA Glenn Research Center β€” Gear Technology publicationsUSA
  4. Numora Editorial Policy. numora.net/editorial-policy