Skip to main content
numora.
numora.

One Rep Max Calculator: Estimate Your Max Safely

Estimate your 1RM from a submaximal set

FitnessByΒ Numora Fitness TeamNot yet reviewed

Try the calculator

Math runs in your browser. No sign-up.

Assumptions
lb
Epley estimate
215.8

185lb for 5 reps suggests a one-rep max near 212.

Brzycki estimate208.1
Average of the two212
85% training load180.2
Embed this calculator on your own site β€” drop in a one-line iframe.
Quick takeaway

A one-rep max is the heaviest load you could lift once, and it anchors almost every strength programme because training percentages are expressed against it. Actually testing a true 1RM is fatiguing and carries injury risk, so most lifters estimate it from a set taken close to failure. This calculator reports two of the best-established estimates β€” Epley and Brzycki β€” alongside their average and a full percentage table. The two formulas agree closely at moderate rep counts and diverge as reps climb, which is itself informative: estimates from sets of 3 to 6 are reliable, while anything beyond about 10 reps becomes a measure of endurance as much as strength.

What is an one rep max?

Estimate your one-rep max from a submaximal set without the fatigue and injury risk of a true max attempt. The calculator reports both the Epley and Brzycki equations β€” the two most widely used in strength coaching β€” plus their average and a typical working load. Estimates are most reliable from sets of three to six reps taken near failure; beyond about ten reps the result reflects muscular endurance as much as maximal strength.

The formula

Epley: 1RM = w Γ— (1 + r Γ· 30) Β· Brzycki: 1RM = w Γ— 36 Γ· (37 βˆ’ r)

Source: Epley (1985) and Brzycki (1993) 1RM prediction equations.

Worked examples

1A set of five on the bench press

Inputs
weightLifted: 185repsCompleted: 5
Walkthrough

Five clean reps at 185 lb gives 215.8 by Epley and 208.1 by Brzycki β€” about 4% apart, which is typical in this range. Taking the average of 212 lb as a working max, a programme calling for 85% would prescribe roughly 180 lb. Sets of five are the sweet spot for this estimate: heavy enough to measure strength, light enough to perform safely.

2Ten reps, where the formulas converge

Inputs
weightLifted: 100repsCompleted: 10
Walkthrough

At exactly 10 reps both formulas return the same answer, weight Γ— 4/3, here 133.3 lb. This is a useful sanity check on any 1RM tool. Beyond 10 the two diverge again, with Brzycki rising faster, and both become less trustworthy as endurance rather than strength starts to govern the result.

How to use this calculator

  1. Weight lifted β€” The load on the bar. Units do not matter as long as you are consistent β€” pounds in, pounds out.
  2. Reps completed β€” Clean reps taken to or near failure. Accuracy degrades sharply above 10.
  3. Read the result. Use the worked examples below to sanity-check against a known scenario.

Common mistakes and edge cases

Estimating from a set you stopped early

Both formulas assume the set was taken to or very near failure. Stopping with three reps in reserve understates your max substantially, because the formula treats those unused reps as unavailable.

Using high-rep sets

Accuracy falls off above about 10 reps. A 20-rep set says more about conditioning than maximal strength, and Brzycki in particular becomes unstable as reps rise toward its asymptote.

Treating the estimate as a tested max

An estimate is a planning number for setting training percentages. Attempting the predicted weight as a true single without working up to it is how people get hurt.

Applying it to isolation exercises

These formulas were derived from compound barbell lifts. Rep behaviour on lateral raises or leg extensions differs enough that the estimates do not transfer well.

Frequently asked questions

how do I calculate my one rep max
Take a set near failure and apply Epley, weight Γ— (1 + reps Γ· 30), or Brzycki, weight Γ— 36 Γ· (37 βˆ’ reps). Five reps at 185 lb gives about 216 and 208 respectively.
which formula is more accurate
Neither is universally better. Brzycki is more conservative below 10 reps, Epley slightly higher; they agree exactly at 10. Averaging them is a sensible default for training purposes.
how many reps should I use for the estimate
Three to six. Fewer gives little information beyond the lift itself, while more than ten starts measuring endurance and the error widens considerably.
is it safe to attempt my estimated max
Treat the estimate as a planning figure for setting percentages rather than a target to attempt. A true max attempt needs a proper warm-up progression and ideally a spotter.
does this work for every exercise
It works best for compound barbell lifts, where the formulas were derived. Isolation movements and machines show different rep behaviour and the estimates transfer poorly.

One Rep Max glossary

One-rep max (1RM)
The heaviest load that can be lifted for a single repetition with correct form.
Reps in reserve
How many more repetitions could have been completed. These formulas assume zero.
Epley formula
A linear 1RM estimate: weight Γ— (1 + reps Γ· 30). Published by Boyd Epley in 1985.
Brzycki formula
A hyperbolic 1RM estimate: weight Γ— 36 Γ· (37 βˆ’ reps). More conservative below 10 reps.

How we built this calculator

Methodology

Both formulas model the same observation: the more reps you can perform with a load, the further that load sits below your true maximum. They differ in how they curve. Epley is linear in reps, adding one-thirtieth of the lifted weight per rep. Brzycki is hyperbolic, dividing by a term that shrinks as reps rise, which makes it climb more slowly at low reps and accelerate near its asymptote.

Formula source
Epley (1985) and Brzycki (1993) 1RM prediction equations
Last updated
2026-11-17
Calculation runs
Client-side only
NF
WRITTEN BY
Numora Fitness Team

Sources & references

Every numeric assumption traces to a primary source.

  1. National Strength and Conditioning Association β€” Essentials of Strength Training and ConditioningUSA
  2. Epley B. (1985), Poundage Chart, Boyd Epley WorkoutUSA
  3. Brzycki M. (1993), Strength Testing: Predicting a One-Rep Max from Reps to Fatigue, JOPERDUSA
  4. Numora Editorial Policy. numora.net/editorial-policy